802.11n Wireless Router,with VPN:
1.The 802.11n-lite WIRELESS GATEWAY is a 90Mbps high speed wireless residential gateway
2.V
Introduction
WG7005E11-LFis a high performance 802.11b/g+ wireless gateway with 4-ports
Fast Ethernet Switch for SOHO users to connect multiple PCs to the Internet via
single DSL/Cable line. The 802.11n-lite WIRELESS GATEWAY is
a 90Mbps high
speed wireless residential gateway
specially designed to provide simple and cost
attractive Internet Access solution for both home and SOHO users.
Its wireless LAN IEEE802.11b/g+, 10/100Mbps Ethernet LAN connectivity, and
Ethernet WAN interfaces provide users the flexibility of Internet connection. The
Ethernet WAN interface is defined to link 802.11b/g+ WIRELESS GATEWAY to
Internet through any xDSL or Cable modem, and this connection enabling users
to link to Internet through its built-in 10/100Mbps Ethernet LAN or WLAN (wireless
LAN) interface.
Besides flexibility on LAN connectivity, 802.11b/g+ WIRELESS GATEWAY also
provides network security and management features for users. Network Address
Translation (NAT), Dynamic Host Configuration Protocol (DHCP), advanced
packet filtering with hacker attack monitor, logging and stateful packet inspection
(Firewall-SPI), Universal Plug and Play (UPnP), Dynamic DNS (DDNS), Wi-Fi
Protected Access (WPA), WPA2, and wireless to wire Ethernet bridging are all
supported.
Product Key feature
1.WEP, WPA/WPA2 security.
2.WDS
3.WPS
4. NAT IP sharing
5. Firewall: DoS, SPI, MAC/IP Client Filtering, Hacker Attack Logging, Email
Alert, Intrusion Detection, Key Word Blocking (HTML based)
6. Virtual Server/ Application Layer Gateway/ DMZ
7.Dynamic DNS
8.Universal Plug and Play (UPnP)GUI based management
9.Gateway features such as NAT, DHCP, and firewall. etc, to provide the
capability to construct private network.
10. NTP Time Server
11.Multiple Language UI
Hardware Specification
Processor RT3050
MIPS 24KEc 384Mhz with 32KB I cache/16KB D cache
Embedded 2T2R 2.4G CMOS RF
Embedded 802.11n 1T1R MAC/BBP w/ MLD improvement
Embedded a 7 port Ethernet switch and a 5 port 10/100Mbps PHY
Support 16/32 bit SDR SDRAM (up to 64M bytes)
FLASH and Memory
2 MByte Flash (up to 8MB Flash should be supported)
16 MByte SDRAM, 8x 16Mbit (up to 32MB should be supported)
WAN Features
Dynamic IP
Choosing Dynamic IP mode enables WAN Ethernet port work as DHCP
client to get an IP address from service provider. The Host name is optional,
but may be required by some Service Provider's.
The default MAC address is set to the WAN's physical interface on the
product. User can use MAC clone to copy the MAC address of administrator
and replace the default MAC address.
PPPoE
User can use PPPoE protocol RFC2516 to get dynamic IP address from
ISP. You will be required to enter the PPPoE username and password
originally provided by your Internet Service Provider to get a dynamic IP.
There are 5 parameters that are configurable in the product.
User name
Password
Service name: Some ISP will check to the service name validate the
user
MTU. The default value is 1492 bytes, it is configurable from 1440 to
1492
Idle time. There is an auto-reconnect check box to reconnect PPPoE
connection if connection is dropped. Idle time is configurable as well in
the product. Default value is 20 minutes.
Static IP
The product support static assignment of the IP address netmask default
router and DNS servers.
Web UI allow user to setup information including IP Address, Netmask,
default gateway, DNS Servers
PPTP
The PPTP screen displays the IP Address, Subnet Mask and Default
Gateway. Enter the User ID and Password assigned by ISP. Enter the Idle
Time Out for the Internet connection. Idle time out is the period of time for
which the connection to the Internet is maintained during inactivity. The
default setting is 10 minutes.
Telstra Bigpond (Australia)
DNS proxy
The product supports 2 DNS entries. If the primary DNS server does not
respond to a DNS request, a secondary DNS server is queried.
User can use DHCP client to get dynamic IP address from ISP.
LAN Features
DHCP server for LAN
The product supports Class C addresses on the LAN side. It is capable of administering
253 clients. The Wireless connection is part of the LAN with up to 128 wireless clients.
The user can enable or disable the DHCP server via Web UI server.
The DHCP server manages IP address of the internal local network and provides the IP
address, subnet mask, gateway address and DNS IP address to DHCP client in the
network
LAN IP address
Web server is supported in the product, the default IP address 192.168.1.1. It is allowed
to configure it in the IP pool.
The product has fixed subnet mask at Class C 255.255.255.0
IP address pool is ranged from 192.168.1.100 to 192.168.1.199 as default, which are
allocated for DHCP client. The IP address pool is allowed to be changed by administrator
Wireless Features
Wireless configuration
To enable wireless service, user has to select wireless working mode. There are four
modes are defined in the router.
802.11g only
802.11b only
802.11n only
11b/g/n mixed mode
User has to setup wireless network name (SSID) as an ID to allow wireless client to
access the AP.
All wireless PCs must have the same SSID setting as the Router to be able to
communicate with the router. The configuration will be able to change the SSID to any
alphanumeric value up to 32 characters.
The following characters are not allowed: & > < # any space.
The default wireless channel is 11, which is at 2.467GHz. The wireless channel is
configurable in the UI.
Available wireless channels set in hardware varies per region. Its compliant with regional
regulations.
America 1-11 (default is 6, or Auto if driver is capable), 20/40MHz Aut
Europe 1-13 (default is 6, or Auto if driver is capable), 20/40MHz Auto
Australia and NZ 1-13 (default is 6, or Auto if driver is capable), 20/40MHz Auto
Most of Asia 1-13 (default is 6, or Auto if driver is capable)
Taiwan 1-11 (default auto), 20/40MHz Auto
Korea 1-13 (default is 6, or Auto if driver is capable), 20MHz Only
Japan 1-13 (default is 6, or Auto if driver is capable), 20MHz Only
SSID can be chose to broadcast to all local network clients, if user configures it to disable,
client has to check APs SSID before communication.
Range extension is also supported to extend wireless coverage, it can be enabled or
disabled.
WDS is supported in the product, as the feature enabled, up to 4 WDS link can be set by
specifying their wireless MAC address in the MAC address table. To make WDS
connection, the same Service
No comments:
Post a Comment